понедельник, 11 января 2016 г.

DIY Simple Brass Toilet Paper Holder

DIY Simple Brass Toilet Paper Holder
DIY Simple Brass Toilet Paper Holder

Toilet paper Holder DIYView in gallery


Brass toilet paper holderView in gallery


Ready to tackle this one? It’ll only take about 15 minutes to make, and you’ll love it for years.


DIY Level: Beginner


DIY Brass TP Holder SuppliesView in gallery


Materials Needed:


  • 6-gauge brass wire (example uses a single 1’ length)
  • Two (2) brass screw hooks
  • Heavy duty pliers and/or needlenose pliers
  • Old towel or rag

Clean the wireView in gallery


Before you begin, you’ll want to remember that every time you use pliers to bend your brass wire, you will want to soften the pliers’ potential damaging factor by using an old towel or rag as a buffer between the pliers teeth and the wire itself. Now, to actually start your brass toilet paper holder, begin by wrapping one end of your brass wire in the towel.


Brass wireView in gallery


Grip the very end of your brass wire (covered in towel) with your heavy duty pliers. (Note: The thicker the wire, the lower the gauge, so 6-gauge is pretty thick, meaning it’s not super easy to bend.)


smooth and strong motionView in gallery


In as smooth and strong a motion as possible, curve your pliers-holding wrist toward you to tightly bend the wire’s end.


Create a small hookView in gallery


You’re trying to create a small hook on the end of your wire.


Repeat the bending processView in gallery


Repeat this process (don’t forget the towel’s buffer) on the other end of your wire. The two hooks should be facing the same way.


Grab a roll toilet paperView in gallery


Grab a roll of toilet paper to use as a measuring benchmark.


Measuring tape spaceView in gallery


Also, grab a measuring tape or book that is the width of your toilet paper-holding space.


Lay the measuring toolView in gallery


Lay the measuring tool (in this case, the book) on a work surface with the toilet paper roll on top. This is to help you visualize the space constraints of your toilet paper dispensing space. Also, lay your two brass hooks on the sides of your book, flanges aligned with the sides of your measuring tool and hooks facing inward. The center of your hook arcs will be your target for your brass wire hooks as you craft the toilet paper holder width.


Gently bend the wire brassView in gallery


Gently bend the brass wire evenly so the end loops are even with the centers of your side brass hooks. Looks like a grin, doesn’t it? Feel free to smile back.


Using your pliersView in gallery


Using your pliers of choice and your old towel, begin bending 90-degree corners in your brass wire so it creates a flat line horizontally and two shorter vertical lines (each with a looped end). This longer flat part will be where the toilet paper roll goes. Tip: When trying to create sharper corners, grip the towel-covered wire with pliers in one hand, then use your other hand to bend the remaining wire around the pliers. In other words, to create loops in the wire, move the pliers-holding hand/wrist. To create corners, hold the pliers-holding hand/wrist still and move the rest of the wire.


Bend until the loops line upView in gallery


Bend until the loops line up with the hooks and the lines are relatively straight. This might take some trial and error bending and unbending and rebending. This photo represents the first attempt, and you can see it’s a little off.


satisfactory cornerView in gallery


When the corners and lines are satisfactory, lay the toilet paper holder on a flat surface and check for alignment there. In this example, the left side was raised a bit. I simply used my old towel and pliers to straighten out the longer straight piece.


side a roll of toilet paperView in gallery


Slide a roll of toilet paper onto your brass wire.


hang a toilet paper holderView in gallery


Hold it up in the space where it will hang as a kind of “dry fit.” Consider how high/low you want to hang it, as well as how forward/back you want it. Remember that not all toilet paper rolls are the same size, so you want to allow for larger/thicker rolls if needed.


screw for your firs brass wireView in gallery


Screw in your first brass screw hook, based upon your dry fit.


screwing in screw hooksView in gallery


One trick for easily screwing in screw hooks and screw eyes is to use a screwdriver, hooked into the hook or eye, to turn it near the end as it gets harder to turn. It’s a finger-saver, this tip is.


Measure the positionView in gallery


Measure the position (vertically and horizontally) of your first screw hook so that you can mirror the second screw hook. This will keep everything level and even.


Second screw hookView in gallery


Mark, then screw in your second screw hook. Adjust the hooks so that the openings face upward and slightly backward – opposite the direction most people would pull their toilet paper off.


Simple hang toilet paperView in gallery


With the toilet paper holder’s looped ends facing backward, install it onto your two screw hooks.


DIY Brass Toilet paperView in gallery


Congrats! It looks awesome.


Standing wood storage for toilet paperView in gallery


Such a simple yet unique way to dispense toilet paper in a stylish bathroom. We love the small touch of brass here, a nod to luxury and class. (Which almost makes things even when positioned next to a plunger. Almost.)


Easy toilet paper hangerView in gallery


The beautiful thing about this easy DIY toilet paper holder is that it’s easy to take off, switch out, and put back on. Let’s be honest – the ease of those three steps are key to actually getting it done.


DIY project for toilet paperView in gallery


As with any DIY project, this can be modified and customized to fit your space and needs. You could do the same thing with screw eyes attached to the wall behind the toilet paper roll; the toilet paper would hang against the wall in that instance.


Wood storage for bathroom paperView in gallery


You could also create a triangle and hang it from a single screw hook above the roll. However you choose to make it, we hope you love the simple sophistication of style in the details.


Note: The author is an experienced, although not professional, DIYer. Neither the author nor Homedit is responsible for any injury or damage that may be a result of following this tutorial.


Original article and pictures take http://www.homedit.com/toilet-paper-holder/ site


Комментариев нет:

Отправить комментарий